Aerochoron (EntityTopic, 15)

From Hi.gher. Space

(Difference between revisions)
Line 24: Line 24:
== Geometry ==
== Geometry ==
 +
==coordinates==
 +
The coordinates of an aerochoron of side length 2 are all permutations of:
 +
<blockquote>(±√2, 0, 0, 0)</blockquote>
=== Equations ===
=== Equations ===
*The [[hypervolume]]s of a hexadecachoron with side length ''l'' are given by:
*The [[hypervolume]]s of a hexadecachoron with side length ''l'' are given by:

Revision as of 15:14, 26 March 2017

The aerochoron, also known as the hexadecachoron and the 16-cell, is the dual of the geochoron: it is equivalent to the geochoron with vertices and cells exchanged. This is analogous with how the octahedron is the dual of the cube. It is also the 4-D demicube.

Geometry

coordinates

The coordinates of an aerochoron of side length 2 are all permutations of:

(±√2, 0, 0, 0)

Equations

  • The hypervolumes of a hexadecachoron with side length l are given by:
total edge length = 24l
total surface area = 8√3 · l2
surcell volume = 4√23 · l3
bulk = 16 · l4
  • The cross sections of the aerochoron are:

[!x,!y,!z,!w] ⇒ octahedron

Projection

Vertex-first Projection

The vertex-first projection of the 16-cell is perhaps easiest to understand. It has an octahedral envelope, with the closest vertex lying at the center of the octahedron, with 8 tetrahedral cells surrounding it. The other 8 cells lie “behind” these 8 cells in the W direction, and meet at the opposite vertex.

(image)

Cell-first Projection

The cell-first projection of the 16-cell has a cubical envelope. This projection is interesting in that all the edges of the 16-cell project onto the edges of the cube and the diagonals on the faces of the cube, forming a wireframe of the cube with each face crossed. It corresponds with the two possible ways to inscribe a tetrahedron inside a cube such that the edges of the tetrahedron lie on the faces of the cube.

(image)

The blue edges outline the cell closest to the viewer. Between this cell and the cubical envelope are 4 tetrahedral volumes that correspond with the 4 cells surrounding this blue cell. There are 6 cells that project onto the 6 faces of the cubical envelope (not shown here because they are being viewed edge-on). These 6 cells connect with the other side of the 16-cell, which contains the remaining 5 cells in a dual arrangement to the cells seen here. The following figure shows this opposite cell:

(image)

4D is unique in that the cell-first projection of its hypercube, which is a 3D cube, has the same envelope as the cell-first projection of its cross polytope. Only 2D has the same phenomenon, although in 2D the hypercube and the cross polytope are in fact the same object (the square).

Construction

The 16-cell is so called because it consists of 16 tetrahedra joined 4 to an edge. This method of thinking about the 16-cell, however, can be difficult to visualize. It is relatively easy to understand how 4 tetrahedra sharing a common edge can be “bent” into 4D so that they each share a face with two other tetrahedra. But it is not quite so simple to imagine how 4 sets of tetrahedra attached thus can be assembled into a 16-cell.

Another method of constructing the 16-cell, which may be a bit easier to understand, is to begin with a 3D octahedron and tapering it in both the positive and negative directions along the W-axis. Consider the first case. The process of tapering is simply to stack progressively smaller octahedra on top of each other along the W-axis, until they have vanished to a single point. The tapered object is the trace formed by this process. As we taper the octahedron along the positive W-axis, each of its 8 triangular faces also grow smaller, stacking on top of the larger triangles behind it. At the end of the taper, the triangles vanish into a common apex. Thus, the tapering process forms 8 tetrahedral cells bent into the positive W-axis. This forms half of the 16-cell, with the apex being the +W vertex of the 16-cell. Now we repeat the same process in the negative W-axis, and we get another 8 tetrahedral cells in exactly the same formation, except that they are now bent in the negative W-axis, and form another apex on the opposite point, which is the -W vertex of the 16-cell. Joining these two halves together at their octahedral base, we obtain the entire 16-cell. The remaining 6 vertices of the 16-cell are precisely the 6 vertices of the octahedron we started out with.

With this understanding of the 16-cell, it is easy to see why it is the 4D equivalent of the octahedron. Just as the 2D square diamond is a 1D line segment tapered in the positive and negative Y-axis, and the octahedron is the 2D square diamond tapered in the positive and negative Z-axis, the 16-cell is the octahedron tapered in the positive and negative W-axis.

Incidence matrix

Dual: geochoron

#TXIDVaEa3aC1aTypeName
0 Va = point ;
1 Ea 2 = digon ;
2 3a 33 = triangle ;
3 C1a 464 = tetrahedron ;
4 H4.1a 8243216 = aerochoron ;

Usage as facets

This polytope does not currently appear as facets in any higher-dimensional polytopes in the database.


Cross polytopes
diamondoctahedronaerochoronaeroteronaeropeton


Demihypercubes
tetrahedronaerochorondemipenteractdemihexeract


Notable Tetrashapes
Regular: pyrochoronaerochorongeochoronxylochoronhydrochoroncosmochoron
Powertopes: triangular octagoltriatesquare octagoltriatehexagonal octagoltriateoctagonal octagoltriate
Circular: glomecubinderduocylinderspherindersphonecylindronediconeconinder
Torii: tigertorispherespheritorustorinderditorus


10. [IIII]
Geochoron
11. <IIII>
Aerochoron
12. (IIII)
Glome
List of bracketopes